Search Results

Standard

Heat Treatment of Low-Alloy Steel Parts Minimum Tensile Strength 220 ksi (1517 MPa) and Higher

2009-07-20

HISTORICAL

AMS2759/2E

This specification, in conjunction with the general requirements for steel heat treatment covered in AMS2759, establishes the requirements for heat treatment of low-alloy steel parts to minimum ultimate tensile strengths of 220 ksi (1517 MPa) and higher. Parts are defined in AMS2759.

Standard

Washers, Spring Lock, Corrosion Resistant Steel, 18Cr - 9Ni

2007-08-24

CURRENT

AMS7241C

This specification covers plain helical lock washers fabricated from corrosion-resistant steel.

Standard

Heat Treatment of Low-Alloy Steel Parts Minimum Tensile Strength 220 ksi (1517 MPa) and Higher

2007-08-24

HISTORICAL

AMS2759/2D

This specification, in conjunction with the general requirements for steel heat treatment covered in AMS 2759, establishes the requirements for heat treatment of low-alloy steel parts to minimum ultimate tensile strengths of 220 ksi (1517 MPa) and higher. Parts are defined in AMS 2759.

Standard

Washers, Spring Lock, Carbon Steel

2007-07-19

CURRENT

AMS7240F

This specification covers plain helical lock washers fabricated from heat treated carbon steel.

Standard

Heat Treatment of Carbon and Low-Alloy Steel Parts Minimum Tensile Strength Below 220 ksi (1517 MPa)

2007-06-13

HISTORICAL

AMS2759/1D

This specification, in conjunction with the general requirements for steel heat treatment covered in AMS 2759, establishes the requirements for heat treatment of carbon and low-alloy steel parts to minimum ultimate tensile strengths below 220 ksi (1517 MPa). Parts are defined in AMS 2759.

Standard

Washers, Spring Lock, Corrosion Resistant Steel 18Cr - 9Ni

2006-06-07

HISTORICAL

AMS7241B

This specification covers plain helical lock washers fabricated from corrosion-resistant steel.

Standard

Washers, Spring Lock Carbon Steel

2006-06-07

HISTORICAL

AMS7240E

This specification covers plain helical lock washers fabricated from heat treated carbon steel.

Standard

Steel, Bars, Forgings, and Tubing, 1.0Cr (0.98 - 1.10C) (SAE 51100) for Bearing Applications

2006-05-15

CURRENT

AMS6449E

This specification has been declared NONCURRENT by the Aerospace Materials Division, SAE, as of September 1995. It is recommended, therefore, that this specification not be specified for new designs. Alloy: 51100 UNS Number: G51986

Standard

Steel, Welding Wire 0.78Cr - 1.8Ni - 0.35Mo - 0.20V (0.33 - 0.38C) Vacuum Melted, Environment Controlled Packaging

2004-12-14

HISTORICAL

AMS5029C

This specification covers a low-alloy steel in the form of welding wire.

Standard

Steel Bars and Forgings 0.50cr (0.98-1.10c) (SAE 50100) for Bearing Applications

2003-09-05

CURRENT

AMS6442G

This specification covers a low-alloy steel in the form of bars, forgings, and forging stock. Primarily for parts of small cross-section, such as needle bearings, requiring a through-hardening steel usually with hardness of approximately 60 HRC and subject to very rigid inspection standards.

Standard

Steel Tubing (Seamless for Machined Parts) 1.8ni 0.80cr 0.25mo (0.38 - 0.43c) Heat Treated (200,000 Tensile Strength)

2002-12-16

CURRENT

AMS6420

Standard

Steel Tubing (Seamless for Machined Parts) .55ni .25mo (.33 - .38c) Normalized Or Heat-Treated (90,000 Tensile Strength)

2002-12-16

CURRENT

AMS6283

Standard

Steel Tubing (Seamless for Machined Parts) .55ni .50cr .25mo (.35 - .38c) Heat-Treated (125,000 Tensile Strength)

2002-12-16

CURRENT

AMS6284

Standard

Steel Tubing (Seamless for Machined Parts) .55ni .50cr .25mo (.38 - .43c) Heat-Treated (180,000 Tensile Strength)

2002-12-16

CURRENT

AMS6285

Standard

Steel Tubing (Seamless for Machined Parts) .55ni .50cr .25mo (.38-.43c) Heat-Treated (180,000 T.S.)

2002-12-16

CURRENT

AMS6286

Standard

Gas Nitriding and Heat Treatment of Low-Alloy Steel Parts

2002-03-14

HISTORICAL

AMS2759/6A

This document specifies the procedure and requirements for heat treating low-alloy and tool steels and for their subsequent gas nitriding by the use of raw or dissociated ammonia. Specific process parameters are given for Nitralloy 135M, Nitralloy EZ, Nitralloy N, 4140, 4340, D6AC and H11 steels. Additional alloys and steel families (e.g., stainless steels) can also be nitrided using parameters acceptable to the cognizant engineering organization.

Standard

Magnetic Particle Acceptance Criteria for Parts

2001-12-07

HISTORICAL

AMS2442

This specification establishes acceptance criteria for discontinuities revealed by magnetic particle inspection of parts made from wrought, ferromagnetic materials.

Standard

Induction Hardening of Steel Parts

2001-01-01

HISTORICAL

AMS2745

This specification defines the requirements for locally hardening steel parts by the induction hardening method.

Standard

Heat Treatment of Carbon and Low-Alloy Steel Parts Minimum Tensile Strength Below 220 ksi (1517 MPa)

2000-09-01

HISTORICAL

AMS2759/1C

This specification, in conjunction with the general requirements for steel heat treatment covered in AMS 2759, establishes the requirements for heat treatment of carbon and low-alloy steel parts to minimum ultimate tensile strengths below 220 ksi (1517 MPa). Parts are defined in AMS 2759.

Standard

Heat Treatment of Carbon and Low-Alloy Steel Parts, Minimum Tensile Strength Below 220 ksi (1517 MPa)

1996-09-01

HISTORICAL

AMS2759/1A

This specification, in conjunction with the general requirements for steel heat treatment covered in AMS2759, establishes the requirements for heat treatment of carbon and low-alloy steel parts to minimum ultimate tensile strengths below 220 ksi (1517 MPa). Parts are defined in AMS2759.